1、航模術語：

1. Aircraft model terminology:

油門位置: 油門越大，螺旋槳拉力或推力越大，飛機增速快，起飛滑跑距離就短。所以，一般應用zui大功率或zui大油門狀態起飛。

Accelerator position: The larger the accelerator, the greater the propeller pull or thrust, the faster the aircraft grows, and the shorter the takeoff and running distance. So, generally, takeoff should be carried out with high power or high throttle.

離地迎角: 離地迎角的大小決定于抬前輪或抬機尾的高度。離地迎角大，離地速度小，起飛滑跑距離短。但離地迎角又不可過大，離地迎角過大，不僅會因飛機阻力大而使飛機增速慢延長滑跑距離，而且會直接危及飛行an全。

Angle of attack from the ground: The magnitude of the angle of attack from the ground depends on the height of lifting the front wheel or tail of the aircraft. High angle of attack from the ground, low ground speed, and short takeoff distance. But the angle of attack from the ground should not be too large. If the angle of attack from the ground is too large, not only will the aircraft slow down due to high resistance, but it will also directly endanger the flight safety.

襟翼位置: 放下襟翼，可加大升力系數，減小離地速度，因而能縮短起飛滑跑距離。

Flap position: Lowering the flaps can increase the lift coefficient, reduce the ground clearance speed, and thus shorten the takeoff distance.

起飛重量: 起飛重量加大，不僅使飛機離地速度加大，而且會引起機輪摩擦力增加，使飛機不易加速。因此，起飛重量加大，起飛滑跑距離增長。

Takeoff weight: An increase in takeoff weight not only increases the aircraft's takeoff speed, but also causes an increase in wheel friction, making it difficult for the aircraft to accelerate. Therefore, the takeoff weight increases and the takeoff distance increases.

機場標高與氣溫: 機場標高或氣溫升高都會引起空氣密度減小，一放面使拉力或推力減小，飛機加速慢；另一方面，離地速度加大，因此起飛滑跑距離必然增長。

Airport elevation and temperature: An increase in airport elevation or temperature can cause a decrease in air density, leading to a decrease in tension or thrust and slow aircraft acceleration; On the other hand, as the ground clearance speed increases, the takeoff distance will inevitably increase.

跑道表面質量: 不同跑道表面質量的摩擦系數，滑跑距離也就不同。跑道表面如果光滑平坦而堅實，則摩擦系數小，摩擦力小，飛機增速快，起飛滑跑距離短。反之跑道表面粗糙不平或松軟，起飛滑跑距離就長。

Runway surface quality: The friction coefficient of different runway surface qualities results in different running distances. If the surface of the runway is smooth, flat, and solid, the friction coefficient is small, the friction force is small, the aircraft speed is fast, and the takeoff and taxiing distance is short. On the contrary, if the surface of the runway is rough, uneven, or soft, the takeoff run distance will be longer.

風向風速: 起飛滑跑時，為了產生足夠的升力使飛機離地，不論有風或無風，離地空速是一定的。但滑跑距離只與地速有關，逆風滑跑時，離地地速小，所以起飛滑跑距離比無風時短。反之則長。

Wind direction and speed: During takeoff and taxiing, in order to generate sufficient lift to lift the aircraft off the ground, regardless of whether there is wind or no wind, the airspeed above the ground is constant. But the distance of taxiing is only related to the ground speed. When taxiing against the wind, the ground speed is small, so the takeoff taxiing distance is shorter than when there is no wind. On the contrary, it is longer.

滑跑坡度: 跑道有坡度，會使飛機加速力加大或減小。

Rolling slope: The runway has a slope that increases or decreases the aircraft's acceleration force.

2、注意事項

2. Precautions

在制作和放飛中，須特別注意不要讓嬰幼兒、低齡兒童、盲人、過敏體質者、智障患者、精神疾病者，接觸和靠近到模型和零件、工具、膠水、電池等，避免可能出現的任何意外事件.

During production and release, special attention should be paid not to allow infants, young children, blind people, allergic individuals, intellectually disabled individuals, and individuals with mental illnesses to come into contact with or approach models and parts, tools, glue, batteries, etc., to avoid any potential accidents

在航模制作中，一定要避免在昏暗、明火、沙塵、強磁場、高溫、低溫、密閉的室內、運動著的交通工具等環境。當模型制作完成后，余下的零件和工具應該歸入您的工具箱子、模型包裝盒內、或者其他an全的地方，不要隨意放置或丟棄.

In the production of aircraft models, it is necessary to avoid environments such as low light, open flames, sand and dust, strong magnetic fields, high and low temperatures, enclosed indoor spaces, and moving vehicles. After the model is completed, the remaining parts and tools should be placed in your tool box, model packaging box, or other complete place, and should not be placed or discarded casually

本文由大型航空模型制作為您提供，我們的網站是：http://gdzcjy.com我們將以全心全意的熱情為您提供服務，歡迎您的訪問！

This article is provided to you by a large-scale aviation model manufacturer. Our website is: http://gdzcjy.com We will provide you with wholehearted enthusiasm and welcome your visit!